sensor electrodes

Brand Name:CITY

Model Number:A5F

Place of Origin:Britain

...gas. The table below shows the typical response of A5F sensors to a number of common cross-interfering gases. The figures are expressed as a percentage of the primary sensitivity (i.e. carbon monoxide = 100%). Gas Response ...

Brand Name:CITY

Model Number:A5F+

Place of Origin:UK

...AB511-W0X Carbon Monoxide 4 Electrode Electrochemical CO Gas Sensor Features: CiTiceLs may exhibit a response to certain gases in a sample other than the target gas. The table below shows the typical response of A5F+ sensors to a number of common cross-...

Brand Name:MEMBRAPOR

Model Number:CH2O/C-10

CH2O/C-10 Formaldehyde Gas Sensor 3 Electrode Electrochemical Highly Sensitive CH2O Measurement Applications • Continuous Air Quality Monitoring • Safety and Environmental Control Formaldehyde Gas Sensor CH2O/C-10 Cross Sensitivity Data The table bel...

Brand Name:CITY

Model Number:3STF 3ST/F

Place of Origin:Britain

...Sensor 3 Electrode Electrochemical Used As a Smoke Monitor Features: Temperature Dependence The output of a CiTiceL can vary with temperature. The graph here shows the variation in output with temperature for 3ST/F CiTiceLs based on a sample of about 16 sensors...

Brand Name:CITY

Model Number:4COSH

Place of Origin:UK

... outline the performance of sensors supplied within the first 3 months. Output signal can drift below the lower limit over time. Datasheet: Bias Voltage Not required Operating Temperature Range -...

Brand Name:CITY

Model Number:5NFL

Place of Origin:UK

5NFL AF508-W0P Low Range NO Nitric Oxide Gas Sensor 4 Electrode Electrochemical The purpose of this document is to present the performance specification of the 5NFL nitric oxide gas sensor Datasheet: T90 Response Time < 30 seconds Baseline Offset 0 to +3 ...

Brand Name:SensoriX

Model Number:H2S 2000

Place of Origin:Germany

...Electrode Electrochemical Key Features & Benefits: • High range H2S sensor • High capacity • Very Selective Measurement: Measurement Range 0-2000 ppm H,S Lower Detection Limit <20 ppm Filter None Sensitivity ...

Brand Name:SUSA

Model Number:4H2S-AS

Place of Origin:Britain

Product Description: 4H2S-AS three-electrode electrochemical hydrogen sulfide sensor Features: Hydrogen sulfide gas sensor is a device used to monitor the concentration of hydrogen sulfide gas in the ambient air. The semiconductor technology hydrogen ...

Model Number:AA015-000 CNLH

CNLH Oxygen (O2) Gas Sensor Part Numbers: AA015-000 For Oxygen Analyzers 2-Electrode Electrochemical Document Purpose: The purpose of this document is to present the performance specification of the CNLH oxygen gas sensor. This document should be used in ...

Model Number:ME4-SO2

...Sensor Low Power Consumption High Precision High Sensitivity Wide Linear Range Good Anti-interference Ability Profile: ME4-SO2 sulfur dioxide gas sensor is constant potential electrolysis type. Oxidation-reduction reaction with sulfur dioxide and oxygen take place respectively on the working electrode and on the counter electrode...

Brand Name:DDS

Model Number:AQ-7CO

Place of Origin:UK

...Sensor Environment In Air Quality High Stability Key Features: High stability, fast response and recovery, strong environmental stability and small package interchangeable with 4 series Common Applications: 1. Food and Beverage 2. HVAC 3. General Industrial 4. Industrial Safety Introduction AQ+7C0 is a 4-electrode CO sensor designed for ambient air quality applications Features The fourth electrode...

Brand Name:DDS

Model Number:AQ+7NO

Place of Origin:UK

AQ+7NO Nitric Oxide NO Sensor 7Series 4Pin High Precision 4th Electrode Detailed description: The AQ+7NO is a 7-series format nitric oxide sensor equipped with a 4-pin interface. The AQ+7NO requires a +300mV bias voltage. The AQ+7NO has a measurement range...

Brand Name:DDS

Model Number:AQ+7NO2

Place of Origin:UK

AQ+7NO2 Nitrogen Dioxide NO2 Gas Sensors 4th Electrode Environment Air Quality High Precision Detailed description: AQ+7NO2 is a 7-series format nitrogen dioxide sensor equipped with a 4-pin interface. AQ+7NO2 requires a 0V bias voltage. AQ+7NO2 has a ...

Brand Name:DDS

Model Number:AQ+7SO2

Place of Origin:UK

...+7SO2 sulfur dioxide sensor is a 7-series specification with a 4-pin interface. The AQ+7SO2 requires a 0V bias voltage. The AQ+7SO2 has a measurement range of 0 - 20 ...

Model Number:AQ+7H2S

Place of Origin:UK

AQ+7H2S Hydrogen Sulphide Sensor (H2S) Introduction The AQ+7H2S is a 4 Electrode H2S sensor designed for use in environmental air quality applications Key Features: 4th electrode for improved baseline temperature performance Repeatability < ±2% H2S ...

Brand Name:EC

Model Number:DS4-HCHO-100

Place of Origin:Germany

... consists of three electrodes in contact with a solid electrolyte, typically made of high-surface-area noble metals and other materials. Gas diffuses through a porous membrane to the working electrode, where oxidation or reduction reactions occur on the

Brand Name:EC

Model Number:DS4-HCN-50

Place of Origin:Germany

... sensor consists of three catalytic electrodes, a solid electrolyte, and gas diffusion holes. Gas reaches the working electrode through the diffusion holes, where electrochemical oxidation or reduction reactions occur on the porous micro-surface of the

Brand Name:YJJ

Model Number:MPn-4C

Place of Origin:China

... gas sensitive layer on an Al2O3 ceramic substrate, and encapsulates it in a metal housing. When the detected gas is present in the ambient air, the conductivity of the sensor will change, and the higher the concentration of

Model Number:H2/C-5000

Place of Origin:Switzerland

H2/C-5000 3-Electrode Electrochemical Hydrogen Gas Sensor for Safety and Process Control Applications: • Safety and Process Control Important Application Notes: H2 sensors lose >10% of their initial sensitivity within the first month after production bef...

Model Number:7ETO-100

Place of Origin:CN

... immersed in an electrolyte solution: Gas Diffusion: Ethylene oxide gas in the environment diffuses through a porous membrane (gas-permeable membrane) into the sensor’s internal electrolyte. Electrochemical Reaction: At the working electrode (cathode),